• ikidd@lemmy.world
      link
      fedilink
      English
      arrow-up
      2
      ·
      3 months ago

      This right here. If you have to ask this question before you trace a pipe back to it’s source and figure it out for yourself, you should not be fucking with gas lines.

  • deegeese@sopuli.xyz
    link
    fedilink
    arrow-up
    0
    ·
    3 months ago

    That is a gas connection. Screw the flex hose on there and put soapy water on the junction to check for leaks before you open the valve.

      • deegeese@sopuli.xyz
        link
        fedilink
        arrow-up
        1
        arrow-down
        3
        ·
        edit-2
        3 months ago

        check for leaks before you open the valve

        Put the soap on first, then open valve. Are you having a reading comprehension problem or being pedantic?

        • InternetUser2012@lemmy.today
          link
          fedilink
          arrow-up
          2
          arrow-down
          1
          ·
          3 months ago

          Did you read what you wrote or you trying to be an asshole? You literally wrote, check for leaks BEFORE you open the valve.

          • Aussiemandeus@aussie.zone
            link
            fedilink
            arrow-up
            1
            arrow-down
            1
            ·
            3 months ago

            You’re having a reading comprehension problem.

            Put the soap on to check for leaks before turning tap on.

            This implies the soap is to check for leaks

            • InternetUser2012@lemmy.today
              link
              fedilink
              arrow-up
              0
              ·
              3 months ago

              All I said was you need to turn it on to see if it leaks. If you’re explaining how to check for a gas leak, It’s a pretty important step. By reading his comment, if OP knows nothing about it, which is clear by their asking, they could just put soap on it, see no bubbles, and then turn it on and walk away…

              • Aussiemandeus@aussie.zone
                link
                fedilink
                arrow-up
                0
                ·
                3 months ago

                If op doesn’t have the understanding of turning it on to see if it leaks op should hire someone to install their new dryer and return their adult card

    • thrawn@lemmy.world
      link
      fedilink
      arrow-up
      0
      ·
      3 months ago

      I’m in southern California and I think most houses have gas hookups for driers, often with gas stoves and gas water heaters too.

    • CrimeDad@lemmy.crimedad.work
      link
      fedilink
      English
      arrow-up
      0
      ·
      3 months ago

      They work well and just make a lot of sense. However, I think they tend to be more expensive than electric clothes dryers.

          • InternetUser2012@lemmy.today
            link
            fedilink
            arrow-up
            0
            ·
            3 months ago

            If the vent plugs up you’re now having carbon monoxide inside your house, it uses a flame to heat, so more potential for fire. If something goes wrong you can have a gas leak. Electric is install it and forget about it, gas you have to watch it. That being said, I prefer gas, it’s more efficient, just have a carbon monoxide detector in the room with the dryer and clean your vents regularly.

            • JaN0h4ck@feddit.org
              link
              fedilink
              arrow-up
              1
              ·
              3 months ago

              To be fair: Electric dryers are still very much a fire hazard, if they’re not properly maintained. But a much smaller one.

        • applate@lemmy.ca
          link
          fedilink
          arrow-up
          0
          arrow-down
          1
          ·
          3 months ago

          Negative. I bought a new gas dryer ~8 years ago and did plenty of research at the time. Electric dryers are FAR more likely to cause a fire.