Hey friends,

I have a two daisy chained shift registers (74AHC595) which are controlled via an ESP32. I want to set one output to high at a time before switching to the next.

The code seems to work, but the outputs O_9 and O_10 are not staying high (zoom) after setting them, whereas all the other ones are working fine. This is the used code snipped:

pinMode(SHIFT_OUT_DATA, OUTPUT);
pinMode(SHIFT_OUT_CLK, OUTPUT);
pinMode(SHIFT_OUT_N_EN, OUTPUT);
pinMode(SHIFT_OUT_LATCH, OUTPUT);

digitalWrite(SHIFT_OUT_N_EN, LOW);

uint16_t input_bin = 0b1000000000000000;

for(int i=0; i<17; i++){

    byte upper_byte = input_bin >> 8;
    byte lower_byte = input_bin & 0x00FF;

    digitalWrite(SHIFT_OUT_LATCH, LOW);
    shiftDataOut(SHIFT_OUT_DATA, SHIFT_OUT_CLK, MSBFIRST, lower_byte);
    shiftDataOut(SHIFT_OUT_DATA, SHIFT_OUT_CLK, MSBFIRST, upper_byte);
    usleep(10);
    digitalWrite(SHIFT_OUT_LATCH, HIGH);

    delay(10)
    input_bin = input_bin>>1;
} 

Is there anything I’m doing wrong, or any idea on where the problem may lie? I’ve already tried looking for shorts and other error sources, but the design was manufactured on a PCB and no assembly issues are noticeable.

  • Kalcifer@lemm.ee
    link
    fedilink
    English
    arrow-up
    2
    ·
    edit-2
    1 year ago

    Would you not want to shift out the upper byte first? I could be misinterpreting your setup.

  • FuzzChef@feddit.de
    link
    fedilink
    English
    arrow-up
    1
    ·
    1 year ago

    What does shiftDataOut do? You loop over it but you give the whole byte to it anyway in each loop.

  • Kalcifer@lemm.ee
    link
    fedilink
    English
    arrow-up
    2
    arrow-down
    1
    ·
    edit-2
    1 year ago

    The first two lines of the for loop,

    byte upper_byte = input_bin >> 8;
    byte lower_byte = input_bin & 0x00FF;
    

    don’t really accomplish anything. The first line is bit shifting to the right 8, and then you just bitwise and it resulting in the same thing. For example, starting with input_bin:

    1000 0000 0000 0000
    >> 8
    0000 0000 1000 0000
    & 0xFF
    0000 0000 1000 0000
    

    So, every time you go through a cycle of the for loop, you’ll just start with the same values in upper_byte, and lower_byte. To sequentially output each shifted value, you’ll instead want something like:

    output_value = 0b1
    for i = 1 to 16:
        latch(low)
        shift_out(output_value)
        latch(high)
        output_value = output_value << 1
    

    That is, if I interpereted correctly that you want the shift registers to output the following:

    output_count, upper_shift_register, lower_shift_register
    1, 00000000, 00000001
    2, 00000000, 00000010
    3, 00000000, 00000100
    .
    .
    .
    16, 10000000, 00000000
    

    Note: Lemmy has a bug where it doesn’t format some symbols correctly, so the left angle bracket gets formatted as <. The same issue exists for the right angle bracket, the ampersand, and I would presume others.

    • mvirts@lemmy.world
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      I think you got and and or switched, first two lines should be fine for shifting the top 8 bits down.

    • quiescentcurrent@discuss.tchncs.deOP
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      You’re 100% right, I’ve lost ‘i’ somewhere in my debugging process

      byte upper_byte = input_bin >> (8+i) ; byte lower_byte = (input_bin >> i) & 0x00FF;

      • mvirts@lemmy.world
        link
        fedilink
        English
        arrow-up
        1
        ·
        edit-2
        1 year ago

        Hmmmm do you want to write to both shift register at the same time? I say this because you’re looping 16 times, but seem to be sending the high and low bytes out 16 times over rather than one bit each time, although you are shifting the input.