Me too - I’ll use Konsole if I need to have the results up all the time, but Yakuake is my main terminal.

My first reaction would be to acknowledge them as a fellow geek, but that’s because most of the people who live near me would hurt themselves trying to open Notepad. Anyone who knows enough to start hacking my config files would be a welcome guest in my house.

Then I’d kill them with a hammer. :-)

The bill, well-intentioned as it might have been, would disrupt centuries of church dogma

Because the sunk cost of centuries of wrong thinking is more important than protecting children.

In other news, the Catholic Church was unavailable for comment.

It is by will alone I set my mind in motion.

It is by the juice of sapho that thoughts acquire speed, the lips acquire stains.

The stains become a warning.

It is by will alone I set my mind in motion

I do the same thing, using a home-grown Git sync solution to keep my vault synced between my desktop, laptop, and Android phone. Free, and easy to setup on the computers, needed some additional SW on the Android side to get the sync to work.

My EndeavourOS (and the prior Manjaro distro) had all of them installed.

All. Of. Them.

I am so tired of having to scroll through hundreds of Noto fonts to get to the later ones, but I’m afraid, if I uninstall one, something will break on reboot.

I use these too, and Fira Code and Hack for coding.

Define “buggy”. I’ve still got a problem where occasionally when I mouse over the dock, it redraws the icons, but I’m living with that until it hurts enough for me to figure out why.

I moved from a major metro area to middle of forking nowhere several years ago. I kept my library cards from the metro area, which still work for Libby ebook and magazine downloads, while the local rural library is tied into a regional system for the occasional dead tree book.

Not sure if it counts, but obsidian for notes and my daily journal, and latte-dock to replace the stock KDE app bar.

Oh, and emacs with doom for general text editing and most coding tasks.

emacs with doom FTW.

Looking forward to learning how to get tree tabs in FF.

+1 for btop - so much easier to find and kill runaway processes.

Thanks for this - I have been seeing the same symptoms with connecting/disconnecting USB audio devices on a brand new (<24 hours old) Endeavour install. I’ll check pipewire version in the AM.

I just hopped both my laptop and desktop from Manjaro to Endeavour - so far, so good. I’m still restoring files from backup and installing stuff, so it’s still early days, but already things are feeling better.

Oh, right. Because everyone knows Chicago is famously crime-free.

Fair point, and thank you. Let me clarify a bit.

It wasn’t my intention to say ChatGPT isn’t helpful. I’ve heard stories of people using it to great effect, but I’ve also heard stories of people who had it return the same non-solutions they had already found and dismissed. Just like any tool, actually…

I was just pointing out that it is functionally similar to scanning SO, tech docs, Slashdot, Reddit, and other sources looking for an answer to our question. ChatGPT doesn’t have a magical source of knowledge that we collectively also do not have – it just has speed and a lot processing power. We all still have to verify the answers it gives, just like we would anything from SO.

My last sentence was rushed, not 100% accurate, and shows some of my prejudices about ChatGPT. I think ChatGPT works best when it is treated like a rubber duck – give it your problem, ask it for input, but then use that as a prompt to spur your own learning and further discovery. Don’t use it to replace your own thinking and learning.

There was a story once that said if you put an infinite number of monkeys in front of an infinite number of typewriters, they would eventually produce the works of William Shakespeare.

So far, the Internet has not shown that to be true. Example: Twitter.

Now we have an artificial monkey remixing all of that, at our request, and we’re trying to find something resembling Hamlet’s Soliloquy in what it tells us. What it gives you is meaningless unless you interpret it in a way that works for you – how do you know the answer is correct if you don’t test it? In other words, you have to ensure the answers it gives are what you are looking for.

In that scenario, it’s just a big expensive rubber duck you are using to debug your work.

I’m printing PLA+ at 200C nozzle, 60C bed temp. It’s been fine so far with a few failures I’ve filed under “User Error”.

OK, now I’m curious how I change the bed temp settings after the first layer – something in the slicer? I’m using Ultimaker Cura, and have just recently been digging into the advanced settings.

I’d heard about needing to keep the filament dry, but it hasn’t been an issue for me yet. That said, I’ll get what filament isn’t still sealed into a dessicant loaded container ASAP - thanks!

Heat is ~28C outside (90F or so), more in the shed. I’ve no ABS since I’ve I read it’s tough to work with and I haven’t had an application for it yet. I just did a cleaning on the plate, and I’ll see if that makes a difference.